Viktor asked for one diagram showing just the physical connections
between nodes, separate from the logical/VLAN topology: ISP->AX6000,
the in-wall apartment->garage run into P1, 4G router (cellular OOB),
UPS mgmt, the PoE cat6 to the camera, the LAN1 cable to eno1, dark
eno2 fallback + free eno3/4, iDRAC on shared-LOM, and the note that
everything else on the R730 is virtual. Referenced from the ADR next
to the logical SVG.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
While reviewing the single-switch design Viktor asked whether both the
home LAN and the camera VLAN 'go via pfSense which forwards upstream' -
a natural misreading a future reader would repeat. Added a section
spelling out the vmbr0 fork: untagged home LAN is L2-bridged past
pfSense (gateway stays the AX6000, rack outage does not affect it, OOB
via 4G survives), while tagged-30 can only land on the dCCTV interface,
making a pfSense bypass impossible by construction. Includes a compact
ASCII topology for terminal readers alongside the SVG.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Viktor prefers not running two switches, so the TL-SG105PE takes over
all rack duties (apartment uplink, 4G, UPS, camera PoE) and the CCTV
segment moves onto a managed tagged trunk over the existing LAN1 cable:
pfSense net3 re-pointed from vmbr2 to vmbr0 tag=30 (applied live; same
MAC so vtnet3/dCCTV survived untouched). This is safe where the original
802.1Q rejection was not, because the managed switch is the only device
on eno1 and polices VLAN-30 membership. eno2/vmbr2 kept dormant as the
documented fallback. Old SG105E retires to cold spare; PE inherits
192.168.1.6. Glossary Segment term updated (all three segments are now
bridge-tags feeding untagged pfSense vNICs).
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Viktor asked to verify free ports on the garage switch (192.168.1.6)
before finalizing. Logging into it showed it is NOT the TL-SG105PE from
the plan but a pre-existing non-PoE TL-SG105E with 4 of 5 ports in use
(apartment uplink, R730 LAN1, 4G router, UPS) - the single-shared-switch
port-VLAN design written earlier today was based on conflating the two
devices. Corrected: the new TL-SG105PE carries ONLY camera + eno2
uplink (mgmt 10.0.30.6 inside the segment), the old switch is untouched,
and no VLAN config exists anywhere. ADR, topology SVG and networking.md
updated to match.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Viktor and emo are adding the first owned camera at the Sofia site (HiLook
IPC-T241H-C watching the garage / server rack). Viktor asked to finalize
emo's plan; the grilling session resolved emo's five open decisions and
replaced the doc's 802.1Q-trunk idea with the site idiom: a dedicated
physical leg (R730 eno2 -> vmbr2 -> pfSense net3 = dCCTV 10.0.30.1/24),
port-based VLAN split on the shared TL-SG105PE, camera default-deny with
NTP-only egress, Frigate + ha-sofia as the only consumers.
The PVE bridge, pfSense interface, Kea subnet and firewall rules were
applied live this session (hand-managed hosts, backed up). This commit
records the decision (ADR-0017), the glossary terms (Segment / CCTV
segment), the as-built architecture doc, and bumps Frigate's ADR-0016
VRAM budget 2000 -> 2300 MiB for the upcoming NVDEC stream.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
